Frequently Asked Questions

Answers to common questions about water bores, concrete coring, vacuum excavation and geotechnical, environmental and exploration drilling across Sydney and NSW. If your question isn't covered here, get in touch or call 0408 915 449.

Working with BG Drilling

What areas do you service?

We're based in Banksmeadow in Sydney and work on sites across Sydney and New South Wales, in both metro and rural areas. Some of our work reaches further along the east coast, including water bores in the ACT, Victoria and Queensland, and geotechnical, environmental and exploration drilling elsewhere in eastern Australia. If you're not sure whether we cover your site, contact us or call 0408 915 449 with the location.

How do I get a quote?

Call us on 0408 915 449 or send the details through our contact form, and we'll get back to you as soon as we can. To help us quote accurately, tell us the site address, the work you need (for example a water bore, concrete coring, vacuum excavation or a drilling investigation), any hole sizes, depths or testing your engineer or consultant has specified, and what access is like on site. We discuss every job with you before we start, so you know what's involved.

Can you work on tight access or sensitive sites?

Yes. We run dedicated tight access rigs with a small footprint and low impact, plus hand-portable equipment, for basements, rear yards, constrained blocks, the inside of buildings and underground mines. For underground projects we can provide electric-powered rigs with exhaust fans and tubing. On live sites such as car parks, road reserves and rail corridors, our non destructive digging crews core and vacuum excavate each hole past the service depth before a rig sets up, and our personnel are inducted and qualified to work within rail corridors. See our tight access drilling page.

How do you manage safety on site?

We manage safety through our own safety management plan and our Occupational Health and Safety system, with clear roles and accountabilities on every job and a goal of zero harm. Our OHS policies are reviewed every year, and our crews are backed by continuous training and comprehensive equipment maintenance. On live sites we prove underground services with vacuum excavation before a rig sets up, and our environmental management system identifies and controls environmental risks. Read more about our safety and environment approach.

Water Bores

What is bore water?

Bore water is groundwater pumped to the surface from an aquifer, the layer of sand, gravel or rock below ground that holds water. A bore is a drilled hole, lined with casing and screens, that draws that water up, usually with a submersible pump. Built properly, it gives you a permanent supply that doesn't depend on mains water or rainfall. Bore water is used for houses, gardens, tanks and livestock, irrigation and construction sites. Find out more about our water bore drilling.

Is bore water safe to drink?

Bore water isn't automatically safe to drink. Its quality varies from property to property and can change over time, so it should be tested by an accredited laboratory before anyone drinks it. Depending on the ground and what happens on the surface nearby, groundwater can carry bacteria, nitrates, salts, iron or other minerals. Many bores supply stock, gardens and irrigation rather than drinking water. If testing shows the water needs treatment, our sister company BG Water Solutions can advise on bore water filtration. Learn more about our water bore drilling.

How do you find bore water on your property?

Finding bore water starts with the geology. Before drilling, we look at the ground beneath your property, the likely depth to the aquifer and the practical limits of the site, such as rig access, distance from septic systems and boundaries, and where the water is actually needed. Records from nearby bores, where they exist, can also give a useful guide. No method can guarantee water until a hole is drilled, but careful site selection gives you the best chance of a reliable supply. Learn how our water bore drilling process works.

Do I need approval to drill a bore in NSW?

Yes, in most cases. Most new bores in NSW need a water supply work approval from WaterNSW before drilling starts, and irrigation and commercial bores usually need a water access licence as well. Stock and domestic bores generally don't need a licence, but they still need the approval. Once the bore is finished, we complete and lodge Form A, the driller's report the regulator requires for every bore. We prepare and lodge the applications for domestic and irrigation bores as part of the job. See our water bore drilling service.

How deep does a water bore need to be?

A water bore needs to be deep enough to reach an aquifer that gives a reliable supply of suitable water, and that depth varies widely from site to site. It depends on the local geology, how deep the water-bearing layers sit, the water quality at each level and how much water you need. Some bores find water at shallow depth, while others go much deeper. One recent bore we drilled went to 120 m. We assess the ground before drilling and tell you what to expect. Read more about our water bore drilling.

How much does a water bore cost?

The cost of a water bore depends on the site, so we quote each one individually. The main factors are the depth needed to reach a reliable aquifer, the ground being drilled (hard rock and soft sands call for different methods), the bore diameter, casing and screens, rig access and the approvals involved. Pump testing and pump installation also add to the total. Call 0408 915 449 with your location and what the water is for, and we'll give you a quote. You can read about the full process on our water bore drilling page.

Concrete Coring

What is concrete core drilling?

Concrete core drilling, or concrete coring, cuts a precise round hole through a concrete floor, wall, ceiling or pavement and removes the centre as a solid core. It's used to make openings for pipes, cables and other services, to take sample cores so a quality assurance company can test the strength of poured concrete, to core the tops of concrete piles so they can be connected to the pile caps, and to cut through slabs and pavements ahead of drilling investigations. Coring is part of our construction and civil drilling work.

How much does concrete core drilling cost?

The cost of concrete core drilling depends on the job, so we quote each one. The main factors are the hole diameter, the thickness of the concrete, how many holes you need, the amount of steel reinforcement, where the holes are and how easy they are to reach, and how water and slurry need to be managed on site. Send us the hole sizes, concrete thickness and site address, or call 0408 915 449, and we'll give you a quote. See our construction and civil drilling services.

What size holes can you core?

We core holes up to 500 mm in diameter through concrete up to 2 metres thick. That covers everything from a small cable penetration to a large opening for a pipe, as well as sample cores for strength testing. We also core through concrete and bitumen pavements for road pavement investigations, and through slabs ahead of geotechnical, environmental and water bore drilling. If you need a size outside this range, call us to discuss it. Find out more about our concrete coring and civil drilling.

Vacuum Excavation

What is vacuum excavation?

Vacuum excavation is a way of digging that uses compressed air or high pressure water to break up the ground and a vacuum to lift the spoil into a debris tank. Because nothing mechanical strikes the ground, underground cables, pipes, conduits and fibre can be exposed without being cut or damaged. It's also called non destructive digging (NDD), and the water method is known as hydro excavation. It's most often used to locate and prove underground services before drilling or excavation. Learn about our vacuum excavation services.

How does vacuum excavation work?

Vacuum excavation works in two steps: the ground is loosened, then vacuumed away. With air vacuum excavation, compressed air breaks up the soil and the dry spoil is lifted into the tank, so it can often go straight back into the hole as backfill. With hydro excavation, high pressure water cuts faster through hard, compacted or clay ground, but the wet spoil has to be carted away. The crew keeps going until the service is exposed and its depth, size and condition can be recorded. Our trucks and trailers range from 1,000 to 5,000 litres. See our vacuum excavation page.

How much does vacuum excavation cost?

Vacuum excavation is quoted to the job, because the cost depends on what has to be exposed and where. The main factors are the number and depth of potholes or the length of trench, the ground conditions, whether air or water suits the site, the size of unit needed, site access and whether wet spoil has to be carted away. When it's part of one of our drilling jobs, our own crew clears the holes ahead of the rig, so there's no waiting on a separate contractor. Call 0408 915 449 for a quote, or read about our vacuum excavation services.

Geotechnical, Environmental and Exploration Drilling

What is environmental drilling?

Environmental drilling is drilling into the ground to collect soil, groundwater and soil vapour samples so an environmental consultant can check for contamination. The results build a profile of the site and show what remediation or ongoing monitoring is needed. It's often required before a site changes hands, before construction begins, or where an operation has to show it isn't affecting groundwater. We drill to your consultant's sampling program, install monitoring wells, and clean our tooling between samples to prevent cross contamination. Learn more about our environmental drilling services.

What is the difference between RC and diamond drilling?

Reverse circulation (RC) drilling produces rock chip samples, while diamond drilling recovers a solid, intact core of rock. RC uses a down hole hammer and air to bring cuttings up the inside of dual wall rods to the surface, so it's faster and costs less per metre, which suits early exploration and grade control. Diamond coring is slower and costs more, but gives the most accurate picture of a deposit for logging and assay. Many programs use both, with RC defining targets and diamond core confirming them. Read more about our mineral exploration drilling.

Why do you need geotechnical drilling before you build?

Geotechnical drilling tells your engineer whether the ground can safely carry the structure you've designed. It collects soil and rock samples below the planned foundation depth at several points across the site, building a profile of what sits beneath the surface. Skipping it can lead to uneven settling, cracked walls and moving plumbing, and in serious cases a foundation that has to be rebuilt. A geotechnical investigation is also often needed before a build can be approved. We carry out the sampling and testing your engineer specifies. Learn more about our geotechnical drilling services.

Still Have a Question?

Call us on 0408 915 449 or send us the details of your site and the work you need, and we will get back to you.